It’s As Simple As 1, 2, 3, To Test A Chainsaw Ignition Coil With A Multimeter
There is a good chance that the ignition coil has fried and your chainsaw won’t start. We will show you how to use a multimeter to check the ignition coil of your chainsaw. This is an easy and inexpensive way to check if your chainsaw requires service.
A multimeter and a simple test of the chainsaw’s ignition coil is all that is required. It takes only a few minutes. These are the steps to check your ignition switch.
What You’ll Need
There are some things that you will need to test the chainsaw ignition coils with a multimeter. The multimeter and the ignition coil will be required. You can start the testing process once you have these two items.
First, identify the terminals of the ignition coil that are used for primary and secondary windings.
Once you have identified the terminals, switch your multimeter to resistance mode. Measure the resistance between them. If there is no continuity between these terminals, the ignition coil needs to be replaced.
Each wire has two connections. Determine the resistance to Ohms mode of each wire and then measure its resistance between them.
How To Test A Chainsaw Ignition Comil Safely And Easily With A Multimeter
Step 1 – Remove The Cover
First, remove the cover from the ignition coil. You can now check the continuity of the ignition coil by removing the cover. If it is continuous, then the ignition coil works properly and you can move on to the next step.
Step 2 – Disconnect The Spark Plug From The Ignition Coil Wire
The spark plug’s connecting wire connects to the ignition coil. Before starting the chainsaw’s ignition coil, it is important to verify continuity. You can do this by disconnecting the spark plug wire and using a multimeter to check for continuity.
Next, adjust the device to continuity. One prong should be attached to each end of the coil wire. If one prong detects continuity, the wire can be reconnected.
The article about the best oil to use with chainsaws might interest you.
Step 3 – Unscrew The Ignition Coil Retain Screws
You will need a Phillips-head screwdriver to remove the ignition coil retaining screws. Turn counterclockwise and place the screwdriver into the recess on top of each screw.
To loosen them, you may have to use force. You can manually remove them once they have become loose.
Step 4 – Remove The Ignition Coil
The ignition system pushes up the coil, which is part of the chainsaw. The engine won’t start if the coil is bad. To check if the coil is bad, you can use a multimeter.
Step 5 – Connect The Red Probe On The Multimeter To (+) The Terminal Of The Ignition Coil
The ignition coil is the part of the chainsaw engine responsible for activating the machine. The ignition coil converts low voltage from the battery to the high voltage required to start the chainsaw.
To test the ignition coil, a multimeter can be used. The red probe should connect to the (+) terminal.
Step 6 – Connect The Black Probe From The Multimeter To A Negative (-) Terminal On The Ignition Coil
Because of its quick nature, testing the ignition coil on a chainsaw is easy. Connect the multimeter’s dash probe and the negative (+) terminal to test the ignition coil. After connecting the probe, you can turn on the meter to wait for the indication. If the reading is not there, you’ll need to restart.
Step 7 – Turn On Your Multimeter And Set The Resistance Or Ohms To It
You will need to set your multimeter to both Ohms or Resistance in order to test the chainsaw’s ignition coil. First, disconnect the spark plug wire and ground wire from the sparkplug. Next, connect the red wire of the multimeter with the ground wire. The black lead should be connected to the ground. Turn on the multimeter, and set resistance or Ohms.
Step 8 – Hold The Trigger Of Your Chainsaw Down And Test For Resistance
Anyone who has ever used a chainsaw is aware of the dangers involved. It is possible to inflict serious injuries by using this piece. It is important to inspect the ignition coil. A multimeter is useful for this purpose.
How Can I Tell If My Chainsaw’s Coil Is Faulty?
It can be time-saving and cost-saving to determine if your chainsaw’s ignition coil is defective. This is how you can test it using a multimeter.
1. Take the spark plug wire out of the spark plug.
2. Disconnect the negative cable.
3. Connect the red lead of the multimeter to one spark plug terminal, then connect the black lead to ground.
4. Let the engine idle for approximately 400 degrees F.
5. The multimeter can be used to measure the voltage at each spark plug terminal, and then display the results in a table.
6. Replace your chainsaw ignition coil immediately if any readings exceed 14 volts.
How Many Ohms Should A Chainsaw’s Coil Have?
There is no single answer to the question of chainsaw coils. Experts agree that a chainsaw should have at most 0.42 ohms resistance.
This theory is based upon the idea that sparks will not fly out of the chain into your hands or eyes if there is enough resistance.
It is always a good idea to consult your chainsaw’s owner manual for details on the resistance required by your particular model.
How Do You Know If A Coil Has 6 Volts Or 12 Volts.
It is hard to identify the voltage of a coil if it is not marked as either 6 or 12 volt. To check the resistance of the coil, you can use an ohmmeter. The coil should have a resistance less than 1/8th of an ohm. This indicates that it is likely to be 6 volt. It is likely to be 12 volt if the coil has a resistance greater than 1/8th of an ohm.
How Can You Check The Coil On A Husqvarna Chainsaw?
It is essential to ensure that your Husqvarna chainsaw chainsaw chain is in good working order. These are the steps to follow:
1. Take out the spark plug.
2. Check the tip of your chain for wear. Replace the chain if it shows excessive wear or is damaged.
3. Use a quality oil to lubricate the engine and replace worn or damaged parts with new gaskets and screws if necessary.
4. You can check that all screws are tightened by turning them with a wrench. If they aren’t tight enough, use a screwdriver to tighten them until they are.
5. Check the connections to the panel if the unit isn’t working.
Conclusion
A multimeter can be used to test the chainsaw’s ignition coil and help determine if it is in need of replacement.
